Archives for the ‘55-gallon drum smoker’ Category

55-gallon drum smoker

This past fall I took an evening welding class at a local technical school and got very excited about making things out of metal. I already had an old stick welder that I didn’t really know how to use, and I ended up buying a MIG welder–the Hobart Handler 140 from Northern. After making lots of small assemblages out of scrap metal  I managed to build a stool and a couple of plant stands, but I had bigger plans.

There’s something special about creating useful objects. A smoker is a nice combination of supremely useful (preparing sustenance) and slightly frivolous (do you need a smoked pork butt to survive?). There are certainly faster and more efficient ways to cook food, but damn smoked meat is good.

I looked around at commercial smokers and custom hacks and talked to a few connoisseurs, and decided the Weber Smoky Mountain was a good design to start from. It’s simple and effective, and in the end it mostly convinced me that the design need not be complex.

Something appealed to me about using the iconic 55-gallon drum as a building block, so I went out and bought a couple from the local scrap yard. One of them even got immediate use as a beer barrel at Crushtoberfest!

A little sketching on different configurations, and I decided a ‘T’ shape would be simple, stable, and functional, and provide plenty of opportunity to practice the MIG on some thin sheet metal. I laid it out in CAD, which made it easy to generate the intersecting curve between the two barrels.

I printed the curve at full scale and wrapped it onto the barrel, traced the curve, then cut the barrel with a jig saw. The first dry fit was amazingly close (way to go, CAD!) but there was still a lot of grinding here and there to accommodate the ribs in the barrels.

IMG_5010 IMG_5011 IMG_5012

I measured and marked the door openings on the barrels and cut them out with the jig saw.

IMG_5020 IMG_5021

The next step was grinding the paint off. The last thing I wanted was burning paint fumes getting into the food, so every bit of paint needed to go. If I were to do this again I would find another way… sand blasting, chemicals, burning it off, etc… anything but taking it off little by little with an angle grinder. I’ll admit the Gator brand paint & rust remover discs I found at Lowes were very effective (if a bit pricey at 9 bucks a piece). But my shop is now coated with a thin layer of green paint dust, much of which ended up in my nose and likely my lungs.

IMG_5009 IMG_5026 IMG_5002

On the first day of grinding I wore a respirator and glasses but nothing else. After washing my hair three times in a row to get the paint dust out I learned to don more protection. For the insides of the barrels I also used an LED headlamp.

As the barrels were made of surprisingly thin metal (20 gauge) the door openings needed to be reinforced with some angle and rolled sheet metal strips, which were plug welded from the outside and tacked from the inside.

IMG_5050 IMG_5049 IMG_5058 IMG_5059

The doors also needed reinforcement, in the form of sheet metal ribs tacked onto the undersides.

IMG_5056 IMG_5060

I welded small pads onto the barrels and doors for the stainless steel hinges. These pads were ground flat then drilled and tapped.

IMG_5065 IMG_5071 IMG_5070 IMG_5072

After grinding the rest of the paint off I welded the two barrels together. This was a challenge, since the metal was so thin and the fit was far from perfect. To prevent burn-through and warpage I used a “stitching” technique where you put a quick tack weld across the joint, wait a second or less and put another tack next to it, continuing like that for about an inch at a time. Apparently this puts less heat to the metal than a continuous bead, but the end result looks very similar. With a little practice I was even able to bridge relatively large gaps between the barrels with short, controlled beads that build on each other, kind of like ants crossing a stream.

IMG_5078 IMG_5079

I shopped around looking for off-the-shelf replacement grates that would work but none of them were big enough for this guy. So I bought about 80 feet of 1/4″ diameter 304 stainless rod (from onlinemetals.com) and cut it to length on the abrasive chop saw. I scored a piece of 1x pine on the table saw at the proper spacing to use as a jig, and clamped the rods down. The MIG would have been perfect for welding the grates, but I would have needed to buy stainless wire and a separate tank of tri-mix gas (65% argon, 33% helium and 2% CO2). The stainless itself was already pushing my budget, so I bought a handful of stainless welding rods and used the arc welder.

IMG_5080 IMG_5081

Next I drilled holes for the dampers– two sets of three holes at the top and two sets of four holes the bottom. The top ones were made like typical grill dampers with a round rotating plate. The bottom ones needed to be on a curved surface, so they slide along the surface rather than rotating.

IMG_5086 IMG_5087

In both cases the moving damper is retained by screws, so I drilled holes and tacked some steel nuts behind them.

IMG_5091

I then drilled a series of holes to allow the smoke and heat into the top barrel. My step drill bit did an amazing job, but the cordless drill still went through two fully charged batteries getting the job done.

IMG_5097

Next I tacked on some small support tabs for the grates and six small sections of square tube as feet.

IMG_5095 IMG_5096

After a thorough deburring, wire-brushing and degreasing with alcohol, I set about applying a high-temperature grill paint. There are several available but Rustoleum High Heat Brush On was a) available at Lowes and b) didn’t require curing at a high temperature like most of the products I found online. Unfortunately it only comes in black, which is actually slightly brownish. They recommend only applying one coat, which I agree with after trying to touch up a few spots after drying, resulting in some weird gloss differences. I then tried the spray can version of the same paint, but found it to be flat finish (vs. the brush-on which is satin). The lesson here is get it right with the first coat because you really can’t go back and hit it again.

IMG_5108 IMG_5110

While the paint was drying (24 hrs… it’s oil-based) I fabricated some handles out of a 1″ maple dowel. I don’t have a wood lathe but the metal lathe did the job. A few coats of Polycrylic and they’re ready to assemble.

IMG_5102 IMG_5104 IMG_5105 IMG_5106

The smoker can be used in one of two different ways– with charcoal in an expanded metal basket or with wood on a traditional fireplace grate. I suppose I could retrofit some gas burners or even electric heating elements, but that’s a project for another day.

IMG_5128 fire_grate2

And last, final assembly. I bought a 3″ smoker/grill thermometer online, and used some nickel-plated chain for the lid stays. I also fabricated a sheet metal “drip tray” to cover the holes under the food and deflect some of the heat.

IMG_5113 IMG_5117 IMG_5119 IMG_5122 IMG_5123 IMG_5126 IMG_5130 IMG_5133 IMG_5134

IMG_5132

I figured my brother-in-law Pete would make much better use of this than me, so we gave it to him for Christmas. Here he is opening it…

Pete getting his present

 

55-gallon drum smoker, part deux

I’ve had some questions about the details of the smoker, so here I’m posting the CAD model and bill of materials as a reference. NOTE: the CAD model is incomplete… I modeled the major structure (barrels and doors) and then ended up building off the cuff as the smoker took shape. Things like the grates, drip tray, feet, hinge and latch locations, etc. were not modeled but just figured out as I went along. If anyone has questions about the details let me know and I can elaborate.

CAD files:
smoker.stp
smoker.igs
wood_rack.stp
wood_rack.igs
charcoal_basket.stp
charcoal_basket.igs

And here’s an unmodified 55 gallon drum model (minus some of the details, like lid and caps, etc.) in case you want to create your own design:
55gallondrum.stp
55gallondrum.igs

Here’s the bill of materials:

quantity
part source
cost
2
55 gallon barrels local junk yard
varies
various
16 ga. sheet metal pieces welding class supply room
$0
≈10′
1/2″ square steel bar (for fire grate) welding class supply room
$0
various
expanded steel sheet (for charcoal basket) welding class supply room
$0
13
1/4″ x 8′ long round rods, 304 stainless (for cooking grates) onlinemetals.com

$78.66

(delivered)

12×12″
18 ga. 304 stainless steel sheet, item #8983K38 (for dampers) McMaster-Carr 

(mcmaster.com)

 

$8.34

36″
maple dowel rod, item # 97015K82 (for handles) McMaster-Carr 

(mcmaster.com)

 

$4.92
5
304 SS hinges, item # 1549A57 McMaster-Carr 

(mcmaster.com)

 

$18.95
3
304 SS draw latches, item # 1889A37 McMaster-Carr 

(mcmaster.com)

 

$15.18
1
quart of Rustoleum High Heat paint Lowe’s
$14.98
1
3″ BBQ/smoker thermometer amazon.com
$21.99
various screws, nuts, etc.